The Bambu Lab A1 uses about 95 W printing PLA: 0.095 kWh and 1.7 cents per hour at the US average electricity price, or about $1.53 a month if it prints 3 hours a day.
How much power does the Bambu Lab A1 use?
The Bambu Lab A1 averages about 95 W while printing PLA, according to Bambu Lab’s own measurements. That rises to 150 W on PC and 200 W on ABS. Its rated maximum is 350 W on a 110 V supply, and it draws 4.1 to 5.4 W on standby with Wi-Fi connected.
Bambu Lab’s wiki gives each average from a test print of 17 to 19 minutes:
| Material | Average power | Bambu’s test print | Energy per hour | Cost per hour at $0.179/kWh |
|---|---|---|---|---|
| PLA | 95 W | 0.025 to 0.028 kWh in 16 min 58 s | 0.095 kWh | 1.7¢ |
| PC | 150 W | 0.043 to 0.053 kWh in 18 min 34 s | 0.15 kWh | 2.7¢ |
| ABS | 200 W | 0.058 to 0.068 kWh in 18 min 35 s | 0.20 kWh | 3.6¢ |
Most of the gap is the heated bed, which runs far hotter for ABS than for PLA. Bambu Lab’s A1 spec sheet rates ABS and PC “Not Recommended” and PLA, PETG, TPU and PVA “Ideal”. For most owners the PLA row is the one that matters. Bambu Lab publishes no PETG figure for the A1.
Bambu Lab A1 wattage: maximum and standby
The A1 is rated at a maximum of 350 W on 110 V and 1,300 W on 220 V. Its input is 100 to 240 VAC, 50/60 Hz.
| State | Watts | Source |
|---|---|---|
| Standby, no network | 4 to 5.4 W | Bambu Lab Wiki |
| Standby, Wi-Fi connected | 4.1 to 5.4 W | Bambu Lab Wiki |
| Printing PLA, average | 95 W | Bambu Lab Wiki |
| Maximum, 110 V supply | 350 W | A1 spec sheet |
| Maximum, 220 V supply | 1,300 W | A1 spec sheet |
How many amps does the A1 draw on 120 V and 230 V?
At its rated maximum the A1 draws about 2.9 A on a 120 V outlet and 5.7 A on 230 V mains. Each figure is the rated watts divided by the supply voltage:
| Supply | Rated maximum | Amps at maximum |
|---|---|---|
| 120 V outlet | 350 W | 2.9 A (350 ÷ 120) |
| 110 V, the rating’s voltage | 350 W | 3.2 A (350 ÷ 110) |
| 230 V mains | 1,300 W | 5.7 A (1,300 ÷ 230) |
| 220 V, the rating’s voltage | 1,300 W | 5.9 A (1,300 ÷ 220) |
In the US, a print running 3 hours or more is a continuous load under the National Electrical Code (NEC), so a 15 A circuit should carry no more than 12 A. One A1 uses about a quarter of that limit, which leaves room for other printers or devices on the same breaker. To check a whole setup, add everything that shares the breaker in the circuit capacity calculator.
The wiki lists a power factor of 0.41 to 0.64 during printing. Because of that, a plug meter that shows amps or volt-amperes will read higher than watts ÷ volts. Your bill is based on the watts reading.
Does the A1 Combo use more power?
Only slightly. The A1 Combo is the A1 plus the AMS lite filament changer. Bambu Lab measures the AMS lite at 3.69 W while working and 0.96 W on standby. With the AMS lite working throughout a PLA print, the Combo averages about 99 W instead of 95 W. That adds 0.37 kWh per 100 hours of printing, about 7 cents.
How much electricity does the A1 use, and what does it cost?
Multiply the average watts by the hours, divide by 1,000 to get kWh, then multiply by your price per kWh:
kWh = average watts × hours ÷ 1000
cost = kWh × price per kWh
A 4-hour PLA print on the A1:
kWh = 95 × 4 ÷ 1000 = 0.38 kWh
cost = 0.38 × $0.179 = $0.068
The same print on the A1 Combo uses 98.69 × 4 ÷ 1000 = 0.39 kWh, about $0.071. On ABS the A1 uses 0.8 kWh in 4 hours, about 14 cents.
The $0.179 is the US Energy Information Administration’s average residential price for the 12 months ending June 2026. Your own rate may be well above or below it, so use the price on your bill, including delivery charges. The electricity cost calculator runs the same math with your rate, print time and print count.
A1 electricity use per day, month and year
Say the A1 prints PLA 3 hours a day, every day. That uses 0.285 kWh a day and about 104 kWh a year, or $18.62 at $0.179 per kWh. Leaving it on Wi-Fi standby for the other 21 hours raises the year to about $26.
| Period | Printing only | Cost | Printing plus standby | Cost |
|---|---|---|---|---|
| Per day | 0.285 kWh | 5.1¢ | 0.40 kWh | 7.1¢ |
| Per month (30 days) | 8.55 kWh | $1.53 | 11.95 kWh | $2.14 |
| Per year (365 days) | 104 kWh | $18.62 | 145 kWh | $26.03 |
printing per day = 95 W × 3 h ÷ 1000 = 0.285 kWh
standby per day = 5.4 W × 21 h ÷ 1000 = 0.113 kWh
per month = kWh per day × 30
per year = kWh per day × 365
cost = kWh × $0.179
The standby column uses 5.4 W, the top of Bambu Lab’s Wi-Fi standby range, so it is the most standby can add. Printing 6 hours a day doubles the printing column.
What standby costs if you leave it on
Left on all month with Wi-Fi connected, the A1 uses 2.95 to 3.89 kWh in 30 days, or 53 to 70 cents. With the AMS lite on standby too, that rises to 3.64 to 4.58 kWh, about 65 to 82 cents a month. Switching the printer off between jobs saves less than a dollar a month.
How does the A1 compare with other printers?
On PLA the A1 averages 95 W, more than the A1 mini’s 80 W and less than the 105 W Bambu Lab lists for the P1S and X1 Carbon. Its 350 W maximum at 110 V matches the P1S, X1 Carbon and Creality K1C.
| Printer | Average on PLA | Rated maximum, 110 to 120 V | Standby |
|---|---|---|---|
| Bambu Lab A1 | 95 W | 350 W | 4.1 to 5.4 W |
| Bambu Lab A1 mini | 80 W | 150 W | 6.1 to 7.3 W |
| Bambu Lab P1S | 105 W | 350 W | 5.8 to 6 W |
| Bambu Lab X1 Carbon | 105 W | 350 W | 8.7 to 9.9 W |
| Creality Ender 3 (original) | 125 W | 270 W | not published |
| Creality K1C | about 144 W | 350 W | 9 to 11 W |
The Bambu Lab figures come from Bambu Lab’s power wiki, with standby on Wi-Fi. The Ender 3 and K1C averages are third-party meter readings by 3DSolved and game2gether, and game2gether also measured the K1C’s idle draw. The 3D printer power consumption comparison covers more models from six brands, and the electricity cost calculator prices a print on any of them from its watts.
Written by 3D Calculators Team· Published · Updated · Figures last checked
Sources
- Bambu Lab Wiki, Bambu Lab printer and AMS power parameters (accessed 2026-11-08)
- Bambu Lab, A1 technical specifications (electrical parameters, supported filament) (accessed 2026-10-10)
- Bambu Lab Store, Bambu Lab A1 (A1 Combo contents) (accessed 2026-10-10)
- U.S. Energy Information Administration, Electric Power Monthly Table 5.3: Average Price of Electricity to Ultimate Customers (accessed 2026-10-10)
- IAEI Magazine, Thomas A. Domitrovich, 100% vs 80%: choosing the right OCPD solution (quotes NEC Article 100 and 210.20(A)) (accessed 2026-10-10)
- Creality, K1C Carbon 3D Printer support page (specifications: rated power and voltage) (accessed 2026-11-08)
- game2gether, Creality K1C test/review, page 5 (idle power and energy use of a 50-minute PLA Benchy) (accessed 2026-11-08)
- MatterHackers, Creality3D Ender 3 3D printer kit (technical specifications) (accessed 2026-11-08)
- 3DSolved, Facundo Arceo, Ender 3 power consumption (3D printer electricity usage) (accessed 2026-11-08)