3D Calculators Team

The 3D Calculators Team builds the calculators on this site and writes the articles that explain them. Each explainer marks which defaults are cited figures and which are placeholders, links every cited figure to its source, and shows the date the figures were last checked.

Updated

How the team works

The explainer under each calculator writes out how the tool gets its result, so the math can be checked by hand. A default value is either a figure taken from a cited document, such as a data sheet, slicer source code or a government statistic, or a round placeholder that the explainer labels as an example. The Sources list on each page gives the day every document was consulted, and the "Figures last checked" line gives the day the page's numbers were last compared against them.

The help center covers how to use the tools and read their results, and Defaults and sources explains how each default was chosen.

Calculators

Articles

  • power consumption
  • wattage
  • electricity cost

3D printer power consumption compared by model

3D printer power consumption compared: rated maximum watts, measured PLA averages and cost per hour for Bambu Lab, Prusa, Creality, Elegoo and more.

  • pricing
  • print cost

How much do 3D printing services charge?

What 3D printing services charge for a plastic part: online FDM from $1.00, $25 minimum orders, about $95 at Protolabs, and 15 cents a gram at libraries.

  • dimensional accuracy
  • shrinkage
  • flow rate

How to calibrate dimensional accuracy per material

Calibrate dimensional accuracy per material: fix e-steps and flow, print a test part, measure it, and turn the errors into XY, Z and hole compensation values.

  • dimensional accuracy
  • shrinkage
  • moisture

How to print dimensionally accurate nylon parts

Print dimensionally accurate nylon parts: dry the filament, control chamber and cooling, then compensate for print shrinkage and moisture swelling.

  • purge waste
  • multi color
  • flush volume

Do all 3D printers poop? Which ones do and why

Do all 3D printers poop? No. Which printers purge through a chute, why even in one color, the grams each purge wastes, and what to do with the waste.

  • power consumption
  • electricity cost
  • wattage

Ender 3 power consumption: watts, kWh and cost

Ender 3 3D printer power consumption: 80 to 125 W measured on PLA, 270 W or 350 W rated, a 220 or 270 W heated bed, with kWh and cost per print.

  • print cost
  • pricing
  • selling prints

How much does it cost to 3D print a small object?

A small 3D print costs 10 cents to $1 at home in PLA and power. Real model weights and print times, service and library minimums, and how to price small prints.

  • chamber heater
  • ventilation
  • heated bed

What temperature should a 3D printer enclosure be?

Enclosure temperature by filament: 45 °C at most for PLA and TPU, 35 to 50 °C for PETG, 45 to 60 °C for ABS, ASA, PC and nylon, from makers' data sheets.

  • ventilation
  • wattage
  • unit conversion

3D printer exhaust fan: what size and type to use

A 3D printer exhaust fan needs only about 10 to 25 CFM for the heat. Fan types compared by airflow and static pressure, plus DIY wiring, kits and bathroom fans.

  • ventilation
  • unit conversion

3D printer vent hose: diameter and length

A 3D printer vent hose should be 4 inches (100 mm). The duct math behind that size, how long the run can be, and flex hose versus rigid vent pipe.

  • ventilation
  • chamber heater
  • unit conversion

Ender 3 enclosure dimensions: the size that fits

Ender 3 enclosure dimensions: at least 440 × 455 × 465 mm inside, 475 × 470 × 620 mm for the V2, plus Creality's enclosure sizes and volumes in ft³ and m³.

  • chamber heater
  • heated bed
  • wattage

How to heat a 3D printer enclosure

Heat a 3D printer enclosure with the bed at 100 °C and the door shut, or add a thermostat-controlled PTC heater. Watts, heat-up times and DIY safety limits.

  • ventilation
  • power consumption
  • unit conversion

How much ventilation does a 3D printer need?

How much ventilation does a 3D printer need? At least 6 air changes an hour for the room, 96 CFM in a 10 x 12 ft room, or 9 to 23 CFM through an enclosure.

  • ventilation
  • wattage
  • print farm

Inline fan for a 3D printer: what size you need

One 3D printer needs about 9 to 23 CFM of exhaust, and 4-inch inline duct fans are rated 165 to 226 CFM. Fan size, filters, speed and grow tents.

  • ventilation
  • heated bed
  • chamber heater

Enclosure temperature for PLA: how warm is too warm

Keep enclosure air at or below 45 °C (113 °F) for PLA, or the filament softens in the extruder and clogs. When to open the door, and what fan holds 40 °C.

  • ventilation

Can you vent a 3D printer into the attic?

No. The building code sends every exhaust fan's air outdoors, never into an attic, soffit or ridge vent. Where a 3D printer vent can end instead, with clearances.

  • scale
  • unit conversion

What is 1/72 scale? Sizes in inches and mm

1/72 scale means 1 inch on the model is 6 feet in reality. A real foot is 4.23 mm, a meter 13.9 mm, a person 24 mm and a Spitfire 156 mm across.

  • 120v 240v

3D printer voltage switch: 115 V or 230 V?

Set a 3D printer's voltage switch to 115 V in the US and 230 V only on 200 to 240 V mains. Where the switch is, how to check it, and what a wrong setting does.

  • shrinkage
  • dimensional accuracy

ABS vs ASA shrinkage: which one shrinks more

ABS vs ASA shrinkage: about the same. Resin and filament data sheets put both at roughly 0.4 to 0.7%, so start ASA with ABS compensation and measure.

  • shrinkage
  • dimensional accuracy

Does PETG shrink? How much, and compared with PLA

Does PETG shrink? Yes, by under 1%: 0.54 to 0.76% in X and Y and 0.73% in Z in a printed-part study, close to PLA. Plus the value to enter in each slicer.

  • print cost
  • pricing
  • selling prints

How much does it cost to 3D print a dragon?

An articulated 3D printed dragon costs about $0.84 to $2.32 in PLA and power at 27 to 55 cm long. Grams, hours and cost by size, plus how to price one to sell.

  • print cost
  • print time
  • multi color

How much does it cost to 3D print a figure?

What a 3D printed figure or toy costs at home: grams, print hours, filament and electricity for figures from 10 to 60 cm, action figures and fidget toys.

  • print cost
  • print time
  • electricity cost

How much does it cost to 3D print a helmet?

A wearable 3D printed helmet costs about $8 to $33 in PLA and power, a mask $2.50 to $10, and a full suit of armor $200 or more, from real model profiles.

  • pricing
  • selling prints
  • print cost

How much to charge for 3D printed keychains

How much to charge for 3D printed keychains: what one costs to make, a pricing formula, and what you keep at $4, $6 and $8 after Etsy or Square fees.

  • print cost
  • pricing
  • print time

How much does it cost to 3D print LEGO bricks?

A 3D-printed LEGO-compatible 2x4 brick costs about 7 cents in PLA and power, against 21 cents on LEGO's US Pick a Brick. Per brick, per gram and per set.

  • print cost
  • pricing
  • selling prints

How much does it cost to 3D print a miniature?

A 28 to 32 mm miniature costs 10 to 26 cents in resin or PLA. Resin per ml and PLA per gram for real minis, a Warhammer army budget, and what to charge.

  • print cost
  • print time
  • pricing

How much does it cost to 3D print a vase?

What a 3D printed vase costs at home: grams, hours, filament and electricity for vase-mode vases from 13 to 30 cm, solid-wall vases, and what to charge for one.

  • power consumption
  • wattage
  • circuit capacity

How many amps does a 3D printer use?

How many amps does a 3D printer use? About 1 to 3 A at 120 V: 0.7 to 1.7 A while printing, up to 2.9 A at a 350 W peak, plus the outlet and circuit it needs.

  • flush volume
  • multi color
  • purge waste

Flushing volume from PLA to PETG and back

The flushing volume from PLA to PETG and back: Bambu Studio's measured 650 mm³, why color-based tables run low, grams per change and how to raise it.

  • power consumption
  • wattage
  • heated bed

UPS for a 3D printer: size and runtime

Size a 3D printer uninterruptible power supply by watts, not VA, and work out how many minutes its battery holds a print, with Bambu Lab examples.

  • multi color
  • purge waste
  • flush volume

Is multi-color 3D printing worth the filament cost?

Where multi-color filament waste comes from, a worked cost and time example, the cheaper alternatives, and how to slice and paint a model to cut color changes.