What is the e-steps formula?
New e-steps equal the current e-steps times the length you asked for, divided by the length that actually went in. Ask for 100 mm at 93 steps/mm, measure 96 mm, and the new value is 93 × 100 / 96 = 96.88 steps/mm. Under-extrusion raises the number. Over-extrusion lowers it.
new e-steps = current e-steps × requested length / actual length
actual length = mark distance before − mark distance after
error = (actual length − requested length) / requested length
Without a test, you can estimate e-steps from the parts. One motor turn is its full steps times the driver’s microsteps. The gears turn the drive gear, and one drive-gear turn pushes π times its effective diameter of filament:
e-steps = full steps per turn × microsteps × gear ratio / (π × effective drive gear diameter)
A 1.8° motor has 200 full steps per turn and a 0.9° motor has 400, according to Klipper’s documentation. Most drivers run 16 microsteps. The gear ratio is driven teeth over motor teeth. Bondtech gives the BMG’s as 50:17, which Klipper’s docs note is often sold as 3:1.
Worked example: a Bondtech BMG from its parts
Voron Design’s configs give Bondtech 5 mm drive gears a rotation distance of 22.68 mm per gear turn. That is an effective diameter of 22.68 / π = 7.22 mm.
- Steps per motor turn: 200 × 16 = 3,200.
- With the 50:17 gearing: 3,200 × 50 / 17 = 9,412 steps per drive-gear turn.
- E-steps: 9,412 / (π × 7.22) = 415 steps/mm, which matches the 415 Bondtech publishes.
Treat a hardware estimate as a starting point. Klipper’s documentation notes that the drive gear’s grip varies between printers and even between spools. Set the estimate, then run the test below.
How do you calculate e-steps?
Read the current value with M503, mark the filament 120 mm above the extruder, and extrude 100 mm slowly. Measure the mark again; the difference is what went in. Multiply the current value by 100, divide by that length, then send M92 E with the result and M500 to save it.
- Heat the nozzle to the printing temperature of the loaded filament.
- Send
M503. Find the line that starts withM92. The number afterEis your current e-steps. - Mark the filament 120 mm above the extruder’s intake and measure the distance with calipers.
- Send
M83, which puts the extruder in relative mode, thenG1 E100 F60. F60 is 1 mm/s, so the move takes 100 seconds. Klipper’s guide uses a slow rate because fast extrusion builds pressure and skews the result. - Measure from the intake to the mark again.
- Enter both distances. The calculator gives the new value and the commands.
- Send
M92 E<new value>, thenM500. M92 changes the running value. M500 writes it to EEPROM, the board’s settings memory, so it survives a restart.
If the extruded length is more than about 2 mm off, Klipper’s guide says to run the test again. Use the new value as the current one for the second run.
Worked example: an Ender-3 that under-extrudes
These are the calculator’s defaults.
- Current value from M503: 93 steps/mm.
- Mark before: 120 mm. Mark after: 24 mm. Actually extruded: 120 − 24 = 96 mm.
- Error: (96 − 100) / 100 = −4.0%, so the extruder under-extrudes by 4 mm.
- New e-steps: 93 × 100 / 96 = 96.88 steps/mm.
- Commands:
M92 E96.88, thenM500.
The 4 mm miss is over 2 mm, so run the test once more at 96.88.
| Actually extruded (of 100 mm, at 93) | Error | New e-steps |
|---|---|---|
| 90 mm | −10.0% | 103.33 |
| 95 mm | −5.0% | 97.89 |
| 96 mm | −4.0% | 96.88 |
| 98 mm | −2.0% | 94.9 |
| 100 mm | 0.0% | 93 |
| 102 mm | +2.0% | 91.18 |
| 105 mm | +5.0% | 88.57 |
You can also measure the extruded length directly instead of using a mark. Pick “The extruded length itself” and type that length.
What should e-steps be on an Ender 3?
93 steps/mm. Creality’s own Marlin firmware for the Ender-3 sets DEFAULT_AXIS_STEPS_PER_UNIT { 80.00, 80.00, 400.00, 93.00 }, and the fourth number is the extruder. Treat 93 as the factory starting point for the stock extruder, not a guarantee. A 100 mm test shows what your machine needs.
The same Creality configuration enables EEPROM_SETTINGS, so M500 saves a new value on the stock firmware. If you have fitted a geared extruder, 93 no longer applies. Use the hardware mode and the maker’s value instead.
Stock values from each printer’s firmware source:
| Printer | Stock e-steps | Firmware source |
|---|---|---|
| Creality Ender-3 | 93 | Creality Ender-3 Marlin Configuration.h |
| Creality Ender-3 Pro | 93 | Marlin example configuration for the Ender-3 Pro |
| Creality Ender-3 V2 | 93 | Creality Ender-3 V2 Marlin Configuration.h |
| Creality Ender-3 S1 | 424.9 | Creality Ender-3 S1 Marlin Configuration.h |
| Prusa i3 MK3S | 280 | Prusa-Firmware MK3S.h, with the extruder at 32 microsteps |
E-steps for geared extruders
Makers publish e-steps for a 1.8° motor at 16 microsteps. Bondtech notes that the value doubles if you double the microsteps, and also doubles on a 0.9° motor. The calculator applies both rules when you change the motor or driver.
| Extruder | 1.8° motor, 16 microsteps | 1.8° motor, 32 microsteps | 0.9° motor, 16 microsteps |
|---|---|---|---|
| Bondtech BMG | 415 | 830 | 830 |
| LDO Orbiter v2.0 | 690 | 1,380 | 1,380 |
| Sherpa Mini or Voron Clockwork 2 (50:10, Bondtech drive gears) | 705.5 | 1,411 | 1,411 |
Bondtech and the Orbiter v2.0 project page publish their figures directly. The 50:10 row is calculated: Annex Engineering gives the Sherpa Mini 50:10 gearing, and Voron Design pairs 50:10 with Bondtech drive gears at 22.68 mm per turn. That gives 3,200 × 5 / 22.68 = 705.5 steps/mm.
E-steps on Klipper
Klipper sets the extruder in its config file as rotation_distance, the millimeters of filament per motor turn: full steps times microsteps, divided by steps per mm. 93 steps/mm at 200 steps and 16 microsteps is a rotation distance of 34.409 mm. Use the rotation distance calculator for the same 100 mm test on Klipper.
E-steps set how much filament the extruder pushes. The slicer’s flow setting then trims how much plastic each line gets, and the flow rate calculator covers that step.
Built by 3D Calculators Team· Published · Figures last checked
Sources
- Creality, Ender-3 Marlin firmware, Configuration.h (DEFAULT_AXIS_STEPS_PER_UNIT, EEPROM_SETTINGS) (accessed 2026-10-14)
- Creality, Ender-3 V2 Marlin firmware, Configuration.h (accessed 2026-10-14)
- Creality, Ender-3 S1 Marlin firmware, Configuration.h (accessed 2026-10-14)
- Marlin Configurations, Creality Ender-3 Pro (CrealityV1) example Configuration.h (accessed 2026-10-14)
- Prusa Research, Prusa-Firmware MK3S variant (MK3S.h) (accessed 2026-10-14)
- Marlin, M92: Set Axis Steps-per-unit (accessed 2026-10-14)
- Marlin, M500: Save Settings (accessed 2026-10-14)
- Marlin, M503: Report Settings (accessed 2026-10-14)
- Marlin, M83: E Relative (accessed 2026-10-14)
- Klipper documentation, Rotation distance (accessed 2026-10-14)
- Bondtech, BMG extruder (e-step value and 50:17 gearing) (accessed 2026-10-14)
- Orbiter Projects, Orbiter v2.0 (steps/mm at 16 microstepping) (accessed 2026-10-14)
- Annex Engineering, Sherpa Mini Extruder (50:10 gearing) (accessed 2026-10-14)
- Voron Design, Voron 2.4 Octopus Klipper config (Bondtech drive gear rotation_distance, gear ratios) (accessed 2026-10-14)