To reduce 3D printing cost, cut print hours first, then grams. Thicker layers halved the print time in one PLA (polylactic acid) test, 20% infill used 39% less plastic than solid, and a 5 kg spool costs 20% less per kilogram than a 1 kg one. After that, cut failed prints and color changes, and keep the printer busy.
How do you reduce the cost of a 3D print?
Reduce the hours and grams each good part needs. Print thicker layers or with a 0.6 mm nozzle, drop infill to 15 to 20%, and keep two to four walls. Buy filament in 3 to 5 kg spools or refills. Then cut failed prints and color changes, and spread the printer’s fixed cost over more printing hours.
Each saving below comes from a published test, a manufacturer’s figure or a store price.
| Lever | Change | Saving | Trade-off |
|---|---|---|---|
| Layer height | 0.12 mm → 0.28 mm | 51% of print time | 5.5% less tensile force, visible layers |
| Nozzle size | 0.4 mm → 0.6 mm | Up to half the print time | Less fine detail |
| Infill | 100% → 20% | 39% of grams, 41% of time | Less toughness; walls make it up |
| Bulk filament | 1 kg → 5 kg spool | 20% per kg | Spool sits longer, needs dry storage |
| Failures | 12% → 5% failure rate | 7.4% of material and machine cost | Time spent on calibration |
| Utilization | 10% → 25% of the year printing | 59% of the machine-hour cost | Needs the work to fill it |
Layer height: the biggest time saving
The Swiss retailer Galaxus printed the same PLA hook at four layer heights. At 0.12 mm it took 3 h 42 min. At 0.28 mm it took 1 h 49 min, 51% less, using the same 20 g of filament. Thicker layers save hours, not plastic.
Trade-off: tensile force fell from 32.5 kg to 30.7 kg, 5.5% less, and layer lines show more.
Nozzle size: a 0.6 mm nozzle
Prusa lists “print times up to twice as fast” for a 0.6 mm nozzle against the standard 0.4 mm. In Prusa’s lamp example, two perimeters from a 0.6 mm nozzle replaced three from a 0.4 mm nozzle and cut the print by “nearly 9 hours.” Keep layer height under 80% of the nozzle diameter, which is 0.48 mm on a 0.6 mm nozzle.
Trade-off: fine details and small text soften. Strength did not suffer: Prusa measured up to 25.6% more impact energy absorbed with the 0.6 mm nozzle.
Infill percentage and pattern
In Galaxus’s infill test, the same PLA hook used 23 g and 2 h 25 min at 100% infill, and 14 g and 1 h 25 min at 20%. Each 10% of infill added about 5 minutes up to 90%. The last step, 90% to 100%, added 28 minutes.
The pattern matters too. Prusa puts adaptive cubic at about a quarter less material than rectilinear, and honeycomb at about 25% more material and up to twice the time. Lightning infill uses the least plastic of all, because it only holds up the top surfaces.
Trade-off: Prusa calls 10 to 20% “the ideal balance” and says going above 40% makes “very little sense.” It adds that more perimeters give the same toughness gain as infill above 20%.
Wall (perimeter) count
Galaxus printed hooks with 1 to 8 walls from a 0.4 mm nozzle. One wall took 1 h 31 min and 17 g, and eight walls took 2 h 11 min and 22 g. That is about 6 minutes and 1 g per wall on this part. Galaxus settled on four walls (1.6 mm) as the best balance.
Trade-off: UltiMaker notes that “two extra perimeters often add more strength than raising infill from 20 % → 30 %.” Cut infill before you cut walls.
Buy filament by the 3 to 5 kg spool or as refills
Prices on the makers’ US stores on October 8, 2026, before shipping and tax:
| Filament | Price | Per kg |
|---|---|---|
| Polymaker PolyLite PLA, 1 kg | $19.99 | $19.99 |
| Polymaker PolyLite PLA, 3 kg | $49.99 | $16.66 |
| Polymaker PolyLite PLA, 5 kg | $79.99 | $16.00 |
| Bambu Lab PLA Basic, 1 kg with spool | $18.99 | $18.99 |
| Bambu Lab PLA Basic, 1 kg refill | $15.99 | $15.99 |
The 5 kg spool is 20% cheaper per kilogram than the 1 kg spool. The refill saves $3 (16%), but only if you already own a reusable reel, which Bambu Lab sells for $11.99. The filament cost calculator compares spools per kilogram.
Trade-off: a 5 kg spool sits for months, so store it dry.
Failed prints
A failed print costs its filament and machine time up to the point it failed. At a failure rate f, each good part carries an extra f ÷ (1 − f) of material and machine cost. At 12% that is 13.6%. At 5% it is 5.3%. Cutting failures from 12% to 5% takes 7.4% off that cost for every good part. The failed print cost calculator prices your own rate.
Multi-color purge
On a single-nozzle printer, each color change flushes plastic. OrcaSlicer’s default flush is 280 mm³, or 0.35 g of PLA at 1.24 g/cm³. Bambu Lab’s wiki gives three cuts:
- Fewer layers. Going from 0.2 mm to 0.28 mm layers cut a test cube’s changes from 153 to 111, and its waste from 83 g to 61 g.
- More copies per plate. Nine cubes on one plate wasted the same 83 g as one, about 9.2 g per cube.
- A lower flush multiplier. At 0.8, every flush is 20% smaller.
The multi-color waste calculator turns your change count into grams, dollars and hours.
Trade-off: a flush that is too small leaves tinted layers in the new color.
Supports
Organic (tree) supports save plastic but can cost time. In one user’s PrusaSlicer comparison, a part’s grid supports used 31 m of filament, and organic supports used 21 m. The MK4 estimate rose from 15.5 h to 17.4 h, while support removal dropped from about 2 hours to an estimated 5 minutes. If the part was PLA, the 10 m saved is about 30 g (2.98 g per meter of 1.75 mm PLA).
Trade-off: at $0.51 per machine-hour, the extra 1.9 hours cost $0.97, more than the $0.60 of PLA saved at $19.99 per kg. Count your own time and the 2 hours of removal saved outweigh both.
Machine-hour cost and utilization
A printer’s depreciation, maintenance and overhead are fixed per year, so each printing hour carries less of them when the printer runs more. For an $800 printer kept 3 years with no labor counted, the printer hourly rate calculator gives these rates on its other defaults:
| Share of the year printing | Cost per machine-hour |
|---|---|
| 10% | $0.51 |
| 25% | $0.21 |
| 50% | $0.11 |
Electricity is the smallest line. At Prusa’s measured 80 W and 18.16 cents per kWh, the U.S. Energy Information Administration (EIA) residential average, an hour costs about 1.4 cents. Cutting hours saves more through wear than through power. The 3D printer electricity cost calculator works out your own printer’s hourly figure.
Worked example: one PLA hook
Take the Galaxus hook at 0.28 mm layers and 0.8 mm walls. Price it at the 10% utilization machine-hour rate of $0.51, which includes electricity.
| Before | After | |
|---|---|---|
| Infill | 100% | 20% |
| Filament | 23 g from a 1 kg spool at $19.99 | 14 g from a 5 kg spool at $79.99 |
| Print time | 2 h 25 min | 1 h 25 min |
| Filament cost | 23 × $0.0200 = $0.46 | 14 × $0.0160 = $0.22 |
| Machine time | 2.42 h × $0.51 = $1.23 | 1.42 h × $0.51 = $0.72 |
| Cost per hook | $1.69 | $0.94 |
The two changes cut the hook’s cost by 44%. Machine time was the larger line in both cases. Print enough to reach 25% utilization and the machine line falls to 1.42 h × $0.21 = $0.30, for $0.52 per hook. Put your own grams, hours and spool price into the print cost calculator to see your saving. To track it across every job, log each print as a row in a 3D print cost spreadsheet for Excel or Google Sheets.
Written by 3D Calculators Team· Published · Updated · Figures last checked
Sources
- Galaxus, 3D printing: How much infill is needed? (PLA test hooks, 0 to 100% cubic infill) (accessed 2026-10-10)
- Galaxus, How does the wall thickness affect the thickness of your PLA prints? (accessed 2026-10-10)
- Galaxus, Does the layer height influence the thickness of your PLA prints? (accessed 2026-10-10)
- Prusa Research blog, Everything you need to know about infills (accessed 2026-10-10)
- UltiMaker, 3D printing infill density: optimizing strength and speed (accessed 2026-10-10)
- Prusa Research blog, Everything about nozzles with a different diameter (accessed 2026-10-10)
- Prusa Forum, Prusa Slicer 2.6.0 and organic supports quick review (grid vs organic support estimates) (accessed 2026-10-10)
- Polymaker, PolyLite PLA (US store, 1 kg, 3 kg and 5 kg prices) (accessed 2026-10-08)
- Bambu Lab, PLA Basic (US store, spool and refill prices) (accessed 2026-10-08)
- Bambu Lab, Bambu Reusable Spool (250 g) (accessed 2026-10-08)
- Bambu Lab Wiki, Reduce waste during filament change (accessed 2026-09-24)
- OrcaSlicer source, PrintConfig.cpp (purging volume default) (accessed 2026-09-24)
- Bambu Lab, PLA Basic technical data sheet V3.0 (density) (accessed 2026-09-24)
- Prusa Knowledge Base, FAQ: Frequently asked questions (power consumption, maintenance interval) (accessed 2026-09-24)
- U.S. Energy Information Administration, Electric Power Monthly, Table 5.6.B: Average price of electricity to ultimate customers by end-use sector, year-to-date through June 2026 (accessed 2026-09-24)